超高性能混凝土国内外研究与应用进展*

介绍了超高性能混凝土（UHPC）的制备原理和性能特点，对UHPC国内外研究和应用情况进行了综述，指出了我国UHPC研究和应用中存在的问题。结果表明：UHPC是一种具有优异的力学性能、耐久性能和环保效益的新型水泥基复合材料。国外在UHPC理论研究和应用研究方面都取得了大量成果，在实际工程中已经获得了广泛的应用；近年来我国在理论研究和应用方面也得到了快速发展；如何简化UHPC制备工艺、降低生产成本、补偿自收缩是今后的主要研究方向，完善相关规范标准以更好地指导UHPC现浇工程应用是目前首要解决的问题。随着环保和可持续发展理念的日益重视，UHPC这种低碳环保材料将有广阔的发展前景。     

Synthesis and characterization of a novel Ca-alginate-biochar composite as efficient zinc (Zn2+) adsorbent: Thermodynamics,process design,mass transfer and isotherm modeling

In this present work, Ca-alginate-biochar adsorbent has been synthesized, characterized and tested its effectiveness in the removal of aqueous phase Zn²⁺ metal. The removal efficiency was studied under various physicochemical process parameters. External mass transfer model, intraparticle diffusion model and pseudo-first-order and pseudo-second-order models were used to fit the experimental Zn²⁺ adoption kinetic results and to identify the mechanism of adsorption. The desorption studies indicate the possibilities of ion-exchange and physical–chemical adsorption of Zn^2+. The adsorption was best described by Langmuir isotherm model. Thermodynamic parameters suggested that the adsorption process becomes spontaneous, endothermic and irreversible in nature.     

电场对竖直矩形微槽群润湿及表面温度的影响

微槽群在热流密度较大时会达到其毛细极限，可通过主动换热方式之一——电水动力学效应对其进行强化。本文为了研究电场对微槽群表面润湿特性和温度分布的影响，采用平板电极提供电场，蒸馏水作为工质，使用高速相机拍摄微槽内液体润湿长度，测量误差为2.97%～7.46%；使用红外热像仪拍摄电场作用下微槽群表面温度分布，测量误差为2.1%～2.39%。热流密度测量误差范围是9.66%～11.11%。结果表明：电场通过驱动微槽内流体向加热区域流动而提升其润湿性能，且较低热流密度下提升更好。因润湿性能的提升，微槽表面温度得以下降。随着电场增强，微槽横向温度分布的“波峰”、“波谷”差别加大，微槽纵向温度明显降低。当热流密度加大时，温降更为显著，1.4W/cm²热流密度、6kV电压下温降可达到30℃以上。温降的增加反映了电场对微槽的强化润湿进一步提升了微槽换热性能，且电场对较高热流情形下的微槽换热有着更为显著的强化效果。     

Investigation on the effect of EDM process variables and environments on acoustic emission signals

Abstract

The performance of electrical discharge machining (EDM) primarily depends on the spark quality generated in the inter-electrode gap (IEG) between the tool and workpiece. A method for obtaining accurate information about the spark gap is required to effectively monitor the EDM process. The rise and fall of thermal energy in the discharge zone at a rapid rate during the dielectric breakdown produces high-pressure shock waves. This work explores the suitability of using acoustic emission (AE) generated from these shock waves and the elastic AE waves released on the workpiece due to the induced stress to monitor the performance and spark gap in EDM. The information content of the AE signals acquired at various machining conditions was extracted using AE RMS, spectral energy and peak amplitude. These features were able to well discriminate the machining condition, tool material, workpiece material, flushing pressure, current density, the initial surface roughness of the tool. Additionally, the AE signal features had a good and consistent correlation with the performance parameters, including material removal rate, surface roughness (Ra and Rq) and tool wear. The findings lay the groundwork to develop an effective, non-intrusive in-situ AE-monitoring system for performance and IEG condition in EDM.     

基于密闭爆发器试验的发射装药内弹道性能预估

为了预估发射装药的内弹道性能,建立了一种基于密闭爆发器试验检测发射药的静态燃烧性能参数进而预测其装药内弹道性能的方法,采用不同批次的单樟-5/7发射药进行了装药性能预估计算,并基于30 mm火炮对内弹道性能预估精度进行了试验验证。结果表明,采用所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法计算获得的最大膛压为376.0 MPa,与试验测试的膛压平均值388.7 MPa的计算误差为3.27%;计算的炮口初速为1143.5 m/s,与试验测试的炮口初速平均值1156.3 m/s的计算误差为1.11%。所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法具有较高的精度,可对发射药样品不同批次间的内弹道性能进行高效精确的预估,为长期贮存发射药使用寿命的判定及发射药产品的出厂校验提供了一种高效低成本的弹道性能评价方法。     

Technical and economic analysis of solvent-based lithium-ion electrode drying with water and NMP

Processing lithium-ion battery (LIB) electrode dispersions with water as the solvent during primary drying offers many advantages over N-methylpyrrolidone (NMP). An in-depth analysis of the comparative drying costs of LIB electrodes is discussed for both NMP- and water-based dispersion processing in terms of battery pack $/kWh. Electrode coating manufacturing and capital equipment cost savings are compared for water vs. conventional NMP organic solvent processing. A major finding of this work is that the total electrode manufacturing costs, whether water- or NMP-based, contribute about 8–9% of the total pack cost. However, it was found that up to a 2?×?reduction in electrode processing (drying and solvent recovery) cost can be expected along with a $3–6?M savings in associated plant capital equipment (for a plant producing 100,000 10-kWh Plug-in Hybrid Electric Vehicle (PHEV) batteries) using water as the electrode solvent. This paper shows a different perspective in that the most important benefits of aqueous electrode processing actually revolve around capital equipment savings and environmental stewardship and not processing cost savings.     

Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Effect of in-app components,medium, and screen size of electronic textbooks on reading performance,behavior, and perception

Although many app-based textbooks are available for students, reading have not been thoroughly outlined. This study aimed to understand how changes from paper to electronic textbooks have affected the academic reading task, investigate student users’ perceptions of in-app components and screen sizes, and identify issues affecting in-app components and task requirements. A mixed factorial design experiment was employed. Results showed that there were no significant changes in comprehension and time spent reading between print text and the iPad. Yet, student highlighting, notetaking, and reading behavior and perception significantly changed based on condition. In addition, students struggled to use in-app components and found them frustrating especially when accounting for sentence splitting. The findings presented can assist in understanding the changes in student reading behavior, which can be used to improve interface design of future e-textbooks.     

不同润湿表面液体沸腾的分子动力学模拟

采用分子动力学方法研究纳米尺度下液氩在过热基板上的沸腾过程。通过调节固液间相互作用的方式改变壁面润湿性，模拟并分析了壁面润湿性对沸腾过程中能量传递和液体运动情况的影响。结果表明：不同润湿性表面均会发生固液分离的现象，但是固体表面附近吸附的氩原子数密度随润湿性增强而增大；润湿性较强时，液体的能量上升快，热通量高，液体内部温度梯度大，发生固液分离时间早，系统中氩的温度和能量低，上升过程中液氩密度、厚度变化小；润湿性较弱时，液体的能量上升慢，热通量小，液体内部温度梯度小，发生固液分离时间延后，系统中氩的温度、能量更高，上升过程中液氩密度、厚度变化较大。下部气体压力整体上大于上部气体压力，发生固液分离时润湿性越强的表面上液体上下压差越大，首次上升过程能达到的高度越高，所需时间越短。